Yamaha F40–F70 Power Trim & Tilt Motor – Replaces 69W-43880-00 | REC62Y-43880-02

REC62Y-43880-02 is a Recmar replacement power trim and tilt motor for selected Yamaha outboard engines. This 12V, two-wire motor uses a three-hole mounting flange and replaces several commonly fitted Yamaha trim motor part numbers, including 69W-43880-00, 69W-43880-01, 62Y-43880-01 and 62Y-43880-02.

It is suitable for selected Yamaha F40, F50, F60, FT60 and F70 applications fitted with the corresponding trim and tilt assembly. This includes applicable Yamaha FT60BET / FT60B models where the original motor cross-references to one of the replacement numbers listed below.

Key Features

• Replacement power trim and tilt motor for selected Yamaha outboards
• 12V marine electrical motor
• Two-wire connection with ring-terminal connections
• Three-hole mounting flange
• Approximately 8 mm diameter drive shaft
• Approximately 37 mm drive-shaft length
• Direct replacement for multiple Yamaha OEM references
• Manufactured and supplied by Recmar

Product Specifications

Yamaha OEM Cross-References

This Recmar trim motor is used as an aftermarket replacement for the following Yamaha part numbers:

Part numbers may appear with or without spaces, hyphens or the final two-digit Yamaha suffix. For example, 69W4388000 and 69W-43880-00-00 identify the same base reference.

Yamaha Outboard Fitment

This trim motor is associated with selected Yamaha outboards within the following engine families:

Engine horsepower alone is not sufficient to confirm fitment. Yamaha may use more than one trim motor on engines with the same horsepower, depending on model code, production year, serial range and fitted trim assembly.

How to Confirm Compatibility

1. Check the original part number: Look for a Yamaha reference beginning with 62Y, 69W or CS3 on the existing motor or parts catalogue.
2. Confirm the mounting flange: The replacement motor uses a three-hole mounting arrangement.
3. Check the drive shaft: The shaft should measure approximately 8 mm in diameter and 37 mm in length.
4. Check the wiring: Confirm that the existing motor uses the corresponding two-wire electrical arrangement.
5. Verify the engine details: Compare the full Yamaha model code and serial number rather than relying only on horsepower.

What Is Included?

• One Recmar power trim and tilt motor
• Attached electrical cable and terminal connections as supplied

This listing is for the electric trim motor only. It is not a complete hydraulic power trim and tilt assembly and does not include the hydraulic pump, trim cylinders, relays or complete mounting bracket.

Installation Information

Trim motor replacement involves marine electrical components and the outboard's hydraulic trim system. Installation should be completed by a competent marine engineer or technician.

Before installation, isolate the battery, securely support the outboard, inspect the electrical connections and check the condition of the motor seal and adjoining trim pump components. Any seals or fasteners removed during replacement should be inspected and renewed where required.

Frequently Asked Questions

Is REC62Y-43880-02 a genuine Yamaha motor?

No. This is a Recmar aftermarket replacement motor designed for compatible Yamaha trim and tilt systems. Yamaha names and part numbers are used for identification and compatibility purposes only.

Does this fit a Yamaha FT60BET?

It fits applicable FT60BET and FT60B engines whose original trim motor corresponds to Yamaha part number 69W-43880-00, 69W-43880-01 or another cross-reference shown above. The complete model and serial number should still be checked before ordering.

Does it fit every Yamaha 60hp outboard?

No. Yamaha has used different trim motors across its 60hp engine range. Confirm the original part number, mounting arrangement, shaft dimensions and wiring before purchase.

Is this the complete power trim and tilt unit?

No. This product is the electric motor that drives the trim hydraulic pump. It does not include the complete hydraulic pump, reservoir, trim rams or mounting bracket.

How many mounting holes does it have?

The motor uses a three-hole mounting flange. The existing unit should be checked visually before ordering.

What are the drive-shaft dimensions?

The drive shaft measures approximately 8 mm in diameter and 37 mm in length.

Can you confirm fitment from my engine serial number?

Yes. Provide the complete Yamaha model code and serial number. A photograph of the existing motor, wiring and mounting flange can also help confirm the correct replacement.

Yamaha is a registered trademark of its respective owner. This product is an aftermarket replacement manufactured by Recmar and is not manufactured or endorsed by Yamaha. OEM references are provided solely to assist with product identification.